AnatomySensei Search bones, muscles, organs…/
EN

Semispinalis

Musculus semispinalis

The semispinalis is the most superficial layer of the transversospinalis group. It runs from the transverse processes of the thoracic and lower cervical vertebrae up to spinous processes higher up and, as semispinalis capitis, to the back of the skull.

Updated 4 min readFree 3D model, no sign-upSources

Loading 3D model…

Show

Free 3D model of the semispinalis. Whole spine. Drag to rotate, zoom with + and − (or Ctrl + scroll), click a bone to highlight and name it.

Key points

  • The semispinalis is the outer layer of the transversospinalis and spans about four to six vertebrae.
  • It is found in the thoracic region, the neck and the head, but not in the lower back.
  • Semispinalis capitis is the largest muscle at the back of the neck and ends on the occipital bone.
  • It extends the spine and head and is supplied by dorsal rami.

What is the semispinalis?

The semispinalis is the outer layer of the transversospinalis, the deep back muscles that run from transverse processes to spinous processes. Its fibres are the longest in the group, spanning about four to six vertebrae.

Unlike the multifidus, it does not reach the lower back. It has three parts: semispinalis thoracis in the middle of the back, semispinalis cervicis in the neck and semispinalis capitis, which ends on the skull.

Labeled diagram of the semispinalis

This diagram names the 3 structures this page is about: the semispinalis capitis, semispinalis cervicis and semispinalis thoracis. The 3D model at the top of the page shows the same view and can be turned to any side.

Labeled diagram of the semispinalis showing the semispinalis capitis, semispinalis cervicis and semispinalis thoracis
Labeled diagram of the semispinalis.

Where is the semispinalis and how can you feel it?

The semispinalis lies beneath the erector spinae in the thoracic region and beneath the splenius muscles in the neck. Its head part forms a thick column on each side of the midline at the back of the neck.

To feel semispinalis capitis, place your fingers on either side of the midline just below the back of the skull and press your head back against your other hand. Two firm ridges tighten under the fingers, the semispinalis capitis covered by the trapezius.

What are the three parts of the semispinalis?

Semispinalis thoracis runs from the transverse processes of about T6 to T10 to the spinous processes of the upper thoracic and lowest cervical vertebrae.

Back from behind with semispinalis thoracis in blue, semispinalis cervicis in green and semispinalis capitis in amber, from the thoracic spine to the skull
Semispinalis thoracis (blue), cervicis (green) and capitis (amber), seen from behind.

Semispinalis cervicis runs from the transverse processes of the upper five or six thoracic vertebrae to the spinous processes of C2 to C5. Most of it ends on the large spinous process of the axis.

Semispinalis capitis starts on the transverse processes of the upper thoracic vertebrae and C7 and on the articular processes of C4 to C6. It ends on the occipital bone, between the superior and inferior nuchal lines.

Which bones does the semispinalis attach to?

Below, all three parts start on the transverse processes of the thoracic vertebrae, with the head part also using the lower cervical vertebrae. Above, the thoracic and cervical parts end on spinous processes several levels higher.

Back from behind with the semispinalis in orange, the occipital bone in blue, the thoracic vertebrae in green and the cervical vertebrae in amber
Semispinalis (orange) with the occipital bone (blue), the thoracic vertebrae (green) and the cervical vertebrae (amber).

Semispinalis capitis ends on the occipital bone at the back of the skull, filling the area between the two nuchal lines on each side of the midline. Exact vertebral levels vary between textbooks.

What does the semispinalis do?

Working on both sides, semispinalis extends the thoracic spine and the neck, and semispinalis capitis pulls the head back. It is the main muscle that holds the head up when you lean forward over a desk.

Working on one side, the thoracic and cervical parts rotate the spine toward the opposite side. Semispinalis capitis can also help tilt the head toward its own side.

What nerves supply the semispinalis?

The semispinalis is supplied by the dorsal (posterior) rami of the cervical and thoracic spinal nerves. Semispinalis capitis receives branches from the upper cervical dorsal rami, including the greater occipital nerve.

It works with splenius capitis, longissimus capitis and the suboccipital muscles in extending the head. The muscles at the front of the neck, such as longus capitis and longus colli, oppose it.

Common problems with the semispinalis

Semispinalis capitis can be strained with other neck muscles in whiplash and in sudden movements of the head. Long periods with the head bent forward put steady load on it.

The greater occipital nerve passes through semispinalis capitis on its way to the scalp. Pressure on the nerve at this point is one suggested cause of occipital neuralgia, pain at the back of the head. This page describes anatomy only.

Common questions

Is semispinalis capitis the largest neck muscle at the back?

Yes. It is usually described as the largest muscle at the back of the neck.

Does the semispinalis reach the lower back?

No. It is found from the middle of the thoracic spine upward. In the lower back the multifidus takes its place.

Why is it called semispinalis?

The name means "half spinal". It is usually explained by the muscle running along only part of the spine.

Is this 3D model of the semispinalis free?

Yes. The interactive 3D model on this page is free to view and use for study, with no account or download needed.

About this free 3D model of the semispinalis

The interactive 3D model on this page is free to use in your browser, with no sign-up. It is built from scan-based anatomy data, so every bone is a separate, correctly placed shape you can turn and inspect from any side.